[Buttface]

Took the Dalton out today with new TP 4350mha lipo's . I had ben running A123s 6.5V.
Why don't the Hitec 7950TH servos handle the voltage of 7.4 lipos ....(they are supposed to)....... so why don't they? Are they junk? Did I spend over 2 grand on junk servos? WTF??? And I thought JR was bad..

[67fairlane]

I guess the grass aint so green over there in hitec land

[TManiaci]

Originally Posted by Buttface

Took the Dalton out today with new TP 4350mha lipo's . I had ben running A123s 6.5V.
Why don't the Hitec 7950TH servos handle the voltage of 7.4 lipos ....(they are supposed to)....... so why don't they? Are they junk? Did I spend over 2 grand on junk servos? WTF??? And I thought JR was bad..

Maybe you have been fighting a bad Rx all this time... you never had a bad servo... LOL.

[Showtime]

I have had the same problem i have 3 of them that glitch when they are at 7.4 volts but when they are regulated to 6 they are fine. I will call Mike at Hitec this week to see if he can shed any light.

[Buttface]

Originally Posted by TManiaci

Maybe you have been fighting a bad Rx all this time... you never had a bad servo... LOL.

You a funny guy Tman.....hey I need some chinks and a mallet.(my famous saying at work when I am laying stone) Its looking like 7950's are only good enough to chink up stones these days,,,,,,nah they too wide....nevermind lol

[Buttface]

Originally Posted by Showtime

I have had the same problem i have 3 of them that glitch when they are at 7.4 volts but when they are regulated to 6 they are fine. I will call Mike at Hitec this week to see if he can shed any light.

I don't know how that man can sleep at night when Hitec is putting out crap like this....poor guy....now hes got to go to go to bat for there mistakes. Don't they test this stuff before they sell millions of dollars of it to people?
Will Hitec brief Mike on what to say about the problem? I hope they don't point the finger at the user like JR likes to do when they come out with a malfunctioning servo.
Look how long it took them to come out with it. One delay after another ,postponing the release date you would think they got it right.....right? I recall proudly saying to my self "My boys are gettn' it right"......but the whole time they where actually away from there desk doodling on the chalk board and making paper airplanes!!!!!
If I came out with a malfunctioning stone column the consumer would have me cooked on his plater with an apple in my mouth!!
Some body needs to introduce them Hitec boys to man hood.*cracking knuckles*

[Buttface]

Note: When Hitec is good you pronounce it euphorically as Hitec..... when Hitec is bad you despicably pronounce it as Hitec with the effuses on an over pronounced ending prefix. For the 7950Th we are using the later....

[yakken]

Originally Posted by Buttface

Note: When Hitec is good you pronounce it euphorically as Hitec..... when Hitec is bad you despicably pronounce it as Hitec with the effuses on an over pronounced ending prefix. For the 7950Th we are using the later....

i am selling everything and goin back to fishing all the time. its either windy, raining or servo's dont work.lol

[Showtime]

Well I can tell you Mike will and always does take care of his customers. He is a good guy and i am not worried at all. Just a little set back i am sure there is a fix for them.

[GmanBIll]

Sounds like your dead band width is too loose, when mine do that out of the box I check the dead band width and usually end up changing it to a 1 or 2 and they stop shuddering.